Techno-economic-environmental evaluation of a combined tri and dry reforming of methane for methanol synthesis with a high efficiency CO2 utilization

Production of methanol, as a green energy, from syngas is coming into focus. However, natural gas based methanol plants, which are used steam reforming of methane for syngas production, have a high CO₂ emission resulting in the global warming. In this study, a novel process for methanol synthesis is proposed to reduce CO₂ emission. In this regard, natural gas and flue gas are fed to a parallel-series system with tri and dry reforming of methane for syngas production with the optimized stoichiometric number. Then, the produced syngas is converted to methanol in a reactor. Finally, the produced methanol is purified by two distillation towers. The proposed method is compared to a referenced method in the view of technological, economic and environmental metrics. The techno-economic-environmental analysis of the processes reveals that not only the proposed method, as compared to the referenced one, increases CO₂ conversion from 20.93% to 99.22%, but also it is more economical and environmentally friendly. In addition, the global warming potential of the proposed method is almost 60% lower than that for the referenced method due to the lower CO₂ emission. Therefore, the proposed method can save above MUS$ 8 a year by CO₂ capture.     

Locating wind farm for power and hydrogen production based on Geographic information system and multi-criteria decision making method: An application

Hydrogen generation from renewable energy resources is considered as a suitable solution to solve the problems related to the energy sector and the reduction of greenhouse gases. The aim of this study is to provide an integrated framework for identifying suitable areas for the construction of wind farms to produce hydrogen. For this purpose, a combined method of Geographic Information System (GIS) and multi-criteria decision making (MCDM) has been used to locate the power plant in Yazd province. The GIS method in the present study consisted of two parts: constraints and criteria. The constraint section included areas that were unsuitable for the construction of wind farms to produce power and hydrogen. In the present study, various aspects such as physical, economic and environmental had been considered as constraints. In the criteria section, eight different criteria from technical aspects (including average wind speed, hydrogen production potential, land slope) and economic aspects (including distance to electricity grid, distance to urban areas, distance to road, distance to railway and distance to centers of High hydrogen consumption) had been investigated. The MCDM tool had been used to weigh the criteria and identify suitable areas. Analytic Hierarchy Process (AHP) technique was used for weighting the criteria. The results of AHP weighting method showed that economic criteria had the highest importance with a value of 0.681. The most significant sub-criterion was the distance to urban areas and the least significant sub-criterion was the distance to power transmission lines. The results of GIS-MCDM analysis had shown that the most proper areas were in the southern and central sectors of Yazd province. In addition, the feasibility of hydrogen production from wind energy had shown that this province had the capacity to generate hydrogen at the rate of 53.6–128.6 tons per year.     

Optimization and efficiency analysis of methanol SOFC-PEMFC hybrid system

In order to improve the power generation efficiency of fuel cell systems employing liquid fuels, a hybrid system consisting of solid oxide fuel cell (SOFC) and proton exchange membrane fuel cell (PEMFC) is proposed. Utilize the high temperature heat generated by SOFC to reform as much methanol as possible to improve the overall energy efficiency of the system. When SOFC has a stable output of 100 kW, the amount of hydrogen after reforming is changed by changing the methanol flow rate. Three hybrid systems are proposed to compare and select the best system process suitable for different situations. The results show that the combined combustion system has the highest power generation, which can reach 350 kW and the total electrical efficiency is 57%. When the power of the tail gas preheating system is 160 kW, the electrical efficiency can reach 75%. The PEM water preheating system has the most balanced performance, with the electric power of 300 kW and the efficiency of 66%.     

Use of La2O3 with 8YSZ as thermal barrier coating and its effect on thermal cycle behavior,microstructure, mechanical properties and performance of diesel engine operated by hydrogen-algae biodiesel blend

In this present work, the effect of lanthanum oxides (La₂O₃) on the thermal cycle behavior of TBC coatings and mechanical properties such as adhesion strength and microhardness of 8% Yttria Stabilized Zirconia (8YSZ) TBCs were investigated. CoNiCrAlY and aluminium alloy (Al–13%Si) were used as bond coat and substrate materials. 8YSZ and different wt % of La₂O₃ (10, 20, and 30%) top coatings were applied using the atmospheric plasma spray (APS) method. The thermal cycling test for TBC coated samples were conducted at 800 °C in the electric furnace. The XRD pattern shows that the La₂O₃ doped 8YSZ material transformed to cubic pyrochloric structured La₂Zr₂O₇ during thermal cycling. Further, the Taguchi-based grey relation analysis (GRA) method was applied to optimize the TBC coating parameters to achieve better mechanical properties such as adhesion strength and microhardness. And the optimized La₂O₃/8YSZ TBC coating was coated on CRDI engine combustion chamber components. The engine was tested with microalgae biodiesel and hydrogen, and the results were promising for the TBC-coated engine. The engine performance increased while using La₂O₃/8YSZ coated components, and the emissions from engine exhaust gas such as CO, HC, and smoke reduced considerably. It was found that there was no separation crack and spallation of the coating layer in the microstructure. Ultimately, the microstructural analysis of the optimized TBC coated piston sample after 50 h of running in the diesel engine confirmed that the developed coating had a superior thermal insulation effect and longer life.     

关于多功能液压支架拖运车的电控系统设计

本文简介多功能液压支架拖运车的电控系统,包括电控箱的设计和主要电气元件的性能和选择依据。此电控系统能够一般电控系统的各种功能和保护,而且能够通过摄像头做到操作盲区和使用遥控器进行远程控制,从而提高液压支架的拖运效率、降低劳动强度和提高安全保障。     

Cheese ripening in nonconventional conditions: A multiparameter study applied to Protected Geographical Indication Canestrato di Moliterno cheese

A multiparameter study was performed to evaluate the effect of fondaco, a traditional ripening cellar without any artificial temperature and relative humidity control, on the chemical, microbiological, and sensory characteristics of Protected Geographical Indication Canestrato di Moliterno cheese. Ripening in such a nonconventional environment was associated with lower counts of lactococci, lactobacilli, and total viable bacteria, and higher presence of enterococci, in comparison with ripening in a controlled maturation room. Moreover, fondaco cheese underwent accelerated maturation, as demonstrated by faster casein degradation, greater accumulation of free AA, and higher formation of volatile organic compounds. Secondary proteolysis, as assessed by liquid chromatography-mass spectrometry of free AA and low molecular weight peptides, did not show any qualitative difference among cheeses, but fondaco samples evidenced an advanced level of peptidolysis. On the other hand, significant qualitative differences were observed in the free fatty acid profiles and in the sensory characteristics. Principal component analysis showed a clear separation of the fondaco and control cheeses, indicating that ripening in the natural room conferred unique sensory features to the product.     

Western Canadian dairy farmers' perspectives on the provision of outdoor access for dairy cows and on the perceptions of other stakeholders

The provision of pasture and outdoor access for dairy cattle differs around the globe. For example, in Ireland, New Zealand, and Australia, dairy farms are largely pasture based, whereas dairy farms in the United States and Canada are largely confinement based. There is a high level of public support for pasture and outdoor access for dairy cows, and the available evidence shows that dairy cattle are highly motivated to access pasture, especially at night. The decision as to whether to provide outdoor access is typically made by farmers, but little is known about dairy farmers' perspectives on this topic. We investigated perspectives of Western Canadian dairy farmers on outdoor access, as well as how they believe different stakeholders (i.e., the dairy industry, the dairy cows, and the general public) regard outdoor access for dairy cows. Data were collected via (1) 11 focus group discussions with a total of 50 Western Canadian dairy farmers, and (2) semi-structured individual interviews with an additional 6 dairy farmers of Hutterite colonies. Data were analyzed using template analysis. Although most participants in this study did not provide outdoor access on their farms, or only provided outdoor access to certain cow groups, participants generally mentioned that they enjoyed seeing cows on pasture or outdoors. However, participants shared that the Canadian supply management system (including processors) required a consistent flow of production, which was thought to be easier and more economically realized with indoor housing of lactating cows. Participants believed that pasture or outdoor access for dairy cows was desired by the public. Some participants believed that dairy cows prefer to spend time outside under favorable weather conditions, but others felt that cows preferred to stay indoors in modern, ventilated freestall barns. The results of this study describe the perspectives of dairy farmers regarding the views of dairy industry stakeholders as they relate to outdoor access, helping to inform conversations around the provision of outdoor access for dairy cattle.     

Cloning,sequencing and structural analysis of membrane-bound polyphenol oxidase from Granny Smith apples (Malus × domestica Borkh)

The gene sequence coding for the membrane-bound polyphenol oxidase (mPPO) with a length of 1761 bp was cloned by PCR method and shown to contain one highly conserved sequence encoding a di-copper-binding region. The predicted three-dimensional structure of mPPO indicated that the active site was located near two copper ions and composed of a typical bundle of four α-helices. Each of the two catalytic copper ions was coordinated with three histidine residues in the hydrophobic pocket, yielding His 180, His 201, His 210, His 332, His 336 and His 366. Docking studies showed that 4-methylcatechol and chlorogenic acid have different binding models due to different ligand sizes and binding sites in the active centre, and it was found that the smaller compound exhibited a higher affinity for mPPO. Molecular dynamic simulation results indicated that Phe 353 is important in controlling enzymatic activity through influencing substrate coordination in the active site.     

Role of particle shape on the shear strength of sand-GCL interfaces under dry and wet conditions

Interface shear strength of geosynthetic clay liners (GCL) with the sand particles is predominantly influenced by the surface characteristics of the GCL, size and shape of the sand particles and their interaction mechanisms. This study brings out the quantitative effects of particle shape on the interaction mechanisms and shear strength of GCL-sand interfaces. Interface direct shear tests are conducted on GCL in contact with a natural sand and a manufactured sand of identical gradation, eliminating the particle size effects. Results showed that manufactured sand provides effective particle-fiber interlocking compared to river sand, due to the favorable shape of its grains. Further, the role of particle shape on the hydration of GCL is investigated through interface shear tests on GCL-sand interfaces at different water contents. Bentonite hydration is found to be less in tests with manufactured sand, leading to better interface shear strength. Grain shape parameters of sands, surface changes related to hydration and particle entrapment in GCL are quantified through image analysis on sands and tested GCL surfaces. It is observed that the manufactured sand provides higher interface shear strength and causes lesser hydration related damages to GCL, owing to its angular particles and low permeability.